You can order replacement keys for your Lippert Slam Latch for RV Doors # LC54PJ with part # LC230012. These slam latches all use the same key so this is the only replacement you'll need. view full answer...
I have a solution for you, but the Adco SFS AquaShed # 290-52247 is not going to be long enough since it has a maximum length of 447". Instead, you'll want to use the Adco SFS AquaShed RV Cover for Toy Hauler Travel Trailer - Up to 40' Long - Gray # 290-52277, which will fit your 2018 Forest River Heritage Glen 326RL that is 37'-9" long. view full answer...
The Curt RV Bumper 2" Trailer Hitch Receiver part # E-100 which is a fit for a standard 4" x 4" rear bumpers will allow you to tow a trailer up to 3,500 lbs. However, that is what the hitch is rated for and the bumper could be rated for less (must confirm with manufacturer). If so, you could install supports, the Mount-n-Lock SafetyStruts Standard RV Bumper Support Brackets part # MO22FR or installs a frame mount hitch, the Adjustable Width Trailer Hitch Receiver for RVs part # 13703. view full answer...
The TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster # TM89FR sends updated pressure and temperature readings on a 4 minute interval. Between those four minute intervals, the transmitters will check for tire issues every six seconds. If an issue is found, the issue is immediately transmitted to the monitor. view full answer...
To add a wall-mount thermostat to your Advent Air RV Air Conditioner # ACM135 you'll need the Air Distribution Box w/ Wall-Mounted Thermostat # ACRG15. This is a kit is the only way to get that thermostat aside from purchasing a whole new AC system that would come kitted with the thermostat. view full answer...
The correct Fastway e2 Weight Distribution System for a Forest River Heritage Glen 273RL is part # FA92-00-1200 which is rated for up to 1,200 lbs. If this is not the system you have the heavier spring bars can be purchased using the Replacement Trunnion Spring Bar part # FA92-02-1299. The brackets can also be replaced using the Replacement Sway-Control Bracket part # EQ95-01-5600. view full answer...
The SolidStep Manual Fold-Down Steps for 29" to 36" Wide RV Door Frames # LC791575 you referenced fall within your 29-3/8" entry width and 35" entry height so you should have no problems. The steps themselves will be a bit shorter with the legs making up the difference for the 35" entry height.
In my experience most campsites are gravel and the location your steps usually line up with is almost always downhill so you'll have a bit extra leg to make up for the drop, whereas the smaller... view full answer...
Hey Rob, sorry to hear about the problems you had with your current hub/drums. The good news is you did order everything you would need and no additional parts would be necessary. The two pieces you pointed out with your yellow arrows do need to come off as they are parts of the old bearings that were destroyed. view full answer...
Hi Shelly, thanks for the question and it's possible we have something depending on the dimensions of your skylight/sunroof. What most people use for this is the Camco Lights Out Retractable Shade for RV Roof Vents # CAM42913.
Technically it's to cover up vents, but could work for you as when fully extended it measures 19" long x 14-1/8"wide.
You asked about a pillow, and there is one, but again it's for vents is smaller than the aforementioned retractable shade. For a 14" x 14" pillow... view full answer...
The Replacement Service Package for Jensen RV Stereo # JEN94FR does contain the correct remote for your Jensen RV Stereo # JWM40(JWM41). Be sure to check the IR sensors on the stereo(see image) and remote for clear line of sight, and check the battery is in working condition and inserted correctly. view full answer...
The 24x40 etrailer Cargo Carrier for RV Bumper part # e99050 has interior dimensions of 40" wide x 24" deep and capacity of 500 lbs so as long as your folding bike meets these criteria then it will be a great fit. If you're referring to the 24" Extension for etrailer Bumper Mounted RV Cargo Carrier part # e99052, this will need to be purchased separately. view full answer...
You need Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2, part # 8-407-5UC3-EZ. This is the hub comes with the bearings, races, and seals. The drum that is compatible is the Dexter Electric Brake Assembly for 4.4K Axles Manufactured After May 2009 - 10" - Right Hand, part # K23-463-00. This hub is also compatible with the Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 10" - Right Hand - 4,400 lbs, part # K23-479-00. This drum brake self adjusts... view full answer...
I would be happy to help you find the correct replacement leaf spring mounting bolts for your 2020 Forest River Wildwood Heritage Glen 22RBHL Travel Trailer but unfortunately we do not have a break down of the components used on a specific trailer.
The most common bolts used are 9/16" but you will need to remove one of your current bolts and measure the diameter of the bolt and length to confirm the correct replacements.
For example the Wet Equalizer Bolt with Locknut and Grease Zerk... view full answer...
We have exactly what you are looking for.
You will need the MORryde StepAbove RV Steps # MR78RR which are designed for doorways that are 7-3/4" to 30-1/4" wide which is perfect for your 28-1/4" internal doorframe opening, and is designed for entry heights of 34" - 36" which is exactly what you need with your 35-1/2" entry height.
These have a 400lb capacity making them pretty heavy duty, and the adjustable legs allow you to make sure the steps are level and secure even when you are parked... view full answer...
I'm certainly sorry to hear your dinette table was broken, but unfortunately just the brackets alone are not available from the Replacement Leg Kit for etrailer RV Dinette Tables - Surface Mount # e79RR. view full answer...
The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set # LC358590 isn't designed to be used on a travel trailer with the landing gear legs swapped out for smaller rear jack legs. Lippert does make a version designed for a travel trailer (part # LC672136 ) but it has a 10,000lb capacity so you'd be over that.
The controller wouldn't be able to communicate properly with the legs so it would just keep throwing up error codes and wouldn't... view full answer...
Technically, as long as you have the space you could add as many stabilizers as you like to your trailer. The Lippert stabilizers you currently have are great for stabilization, but can't be used for leveling so the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705 ends up being the more useful jack.
If you have the space I would use both and start by leveling the trailer out with the # UF39-941705 and then lowering the Lippert jacks for extra stabilization help.... view full answer...
We do have a cover that fits your 2017 Forest River Wildwood Heritage Glen 300BH, from Adco, and it's the following part number:
- Adco Olefin HD RV Cover for Travel Trailers up to 37' - All Climate + Wind # AD39ZR
Based on my research, your trailer measures just about 37-1/2 feet (including the trailer tongue), so when you take away the length of the tongue you're at 34-1/2 feet, making the # AD39ZR the correct fit. This cover is designed to protect your trailer against any and all weather,... view full answer...
We do have one RV roof vent that can be used with 120 volt power with the Ventline Roof Vent part # V2128SP-01. This would work great with the AC power you have currently there. We don't have any MaxxFans that can be used with this type of power source. view full answer...